build details

Show: section status errors & todos local changes recent changes last change in-page changes feedback controls

Part 1: Altitude PID in Simulation

Modified 2020-11-04 by Sean Hastings

In this part of the project, you will be implementing a PID controller for a simulated drone that can only move in one dimension, the vertical dimension. You can control the speed the motors spin on the drone, which sets the thrust being generated by the propellers. In this system, the process variable is the drone’s altitude, the setpoint is the desired altitude, and the error is the distance in meters between the setpoint and the drone’s altitude. The output of the control function is a PWM (pulse-width modulation) value between 1100 and 1900, which is sent to the flight controller to set the drone’s throttle.

You should implement the discretized version of the PID control function in student_pid_class.py:

u(t) = K_pe(t_k) + K_i\sum_{i=0}^k e(t_i)\Delta t + K_d\frac{e(t_k)-e(t_{k-1})}{\Delta t} + K K_p, K_i, K_d, K = Constants \; and \; Offset \; Term e(t_k) = Error \; at \; Time \; t_k \Delta t = Time \; Elapsed \; from \; Previous \; Iteration

Notice that there is an extra offset term K added to the control function. This is the base PWM value/throttle command before the three control terms are applied to correct the error in the system.

To tune your PID, set the parameters ( K_p, K_i, K_d, K ) in z_pid.yaml.

To test your PID, run python sim.py on your base station or a department computer but not on your drone, since it requires a graphical user interface to visualize the output. The PID class in student_pid_class.py will automatically be used to control the simulated drone. The up and down arrow keys will change the setpoint, and r resets the simulation.

You will need numpy, matplotlib, and yaml to run the simulation. To install these dependencies, run pip install numpy matplotlib pyyaml.

Write brief answers to all exercises in answers_pid.md.

Problem 1: Implement an Idealized PID

Modified 2019-10-29 by andrewkpeterson

Exercises

  1. Implement the step method to return the constant K . At what value of K does the drone takeoff? Set K to 1300 for the remainder of the questions.
  2. Implement the P term. What happens when K_p is 50? 500? 5000?
  3. Implement the D term. Set K_p to zero. What happens when K_d is 50? 500? 5000?
  4. Now tune K_p and K_d so that the drone comes to a steady hover. Describe the trade-off as you change the ratio of K_p to K_d .
  5. Implement the I term and observe the difference between PD and PID control. What role does the I term play in this system? What happens when K_p and K_d are set to zero?
  6. Implement the reset method and test its behavior. If implemented incorrectly, what problems can you anticipate reset causing?
  7. Finally, tune the constants in your PID controller to the best of your abilities. When the setpoint is moving, the drone should chase the setpoint very closely. When the setpoint is still, the drone should converge exactly at the setpoint and not oscillate. Report your tuning values.

Problem 2: Tuning a PID with Latency

Modified 2018-09-01 by Sophie Yang

Now, we introduce latency! Run the simulation as python sim.py -l 6 to introduce 24 milliseconds of latency (six steps of latency running at 25 hz).

Exercises

  1. Tune the constants in your PID controller to the best of your abilities. The drone should chase the setpoint very closely, but will converge more slowly when the setpoint is still. Report your tuning values.
  2. Compare your tuning values to the values you obtained in problem 1.
  3. Explain the effect of latency on each control term.

Problem 3: Tuning a PID with Latency, Noise, and Drag

Modified 2018-09-01 by Sophie Yang

In the most realistic mode, you will tune a controller with latency, noise, and a drag coefficient. You can do this with the command line arguments python sim.py -l 3 -n 0.5 -d 0.02 to be most realistic to real-world flight.

Exercises

  1. Tune with these arguments to be as good as possible. Report your tuning values.
  2. Compare your tuning values to the values from problems 1 and 2.

Run python sim.py -h to see the other simulator parameters. We encourage you to experiment with those and observe their effects on your controller.

After you finish this part of the project, make sure that you push the final versions of the files that you modified to your Github repo.